Search found 214 matches
- Fri Jun 11, 2010 4:28 pm
- Forum: Software Support
- Topic: ebc goes straight to boost cut
- Replies: 7
- Views: 6035
- Mon May 31, 2010 12:16 pm
- Forum: Software Support
- Topic: EBC Still swapping to NO after program close
- Replies: 28
- Views: 29355
- Mon May 31, 2010 12:07 pm
- Forum: Software Support
- Topic: ebc goes straight to boost cut
- Replies: 7
- Views: 6035
- Mon May 31, 2010 10:40 am
- Forum: Software Support
- Topic: ebc goes straight to boost cut
- Replies: 7
- Views: 6035
Hi i had the same problem it was a leak at the westgate no boost control= boost cut check your mac valve set activation with a vacum value , put key ON and you will hear the clicclic noise if not, you have a Mac valve electrical problem: wiring bad soldering.... check your WG vacum/boot hoses thank...
- Mon May 31, 2010 12:30 am
- Forum: Software Support
- Topic: ebc goes straight to boost cut
- Replies: 7
- Views: 6035
- Mon May 31, 2010 12:28 am
- Forum: Software Support
- Topic: ebc goes straight to boost cut
- Replies: 7
- Views: 6035
ebc goes straight to boost cut
Hey, i am having problems with ectune and my mac soleniod. no matter what dc % i set, it goes straight to boost cut. ebc activation : 10psi wg activation: 7psi fixed duty cycle 5% normally closed straight to boost cut any ideas?
- Mon May 10, 2010 11:05 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
i got it working it was not hook up to A11. Now is How do i increase boost? duty cycle? fast spool? any help pls WOOPS!!!!!! ahahha i connected the soleniod to A9, no A11, thats why i got the IACV Error! But i still do not get 12V!! I connected power to Ecu Power, and A11. Measured Volts, got like ....
- Sun May 09, 2010 10:36 am
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
WOOPS!!!!!! ahahha i connected the soleniod to A9, no A11, thats why i got the IACV Error! But i still do not get 12V!! I connected power to Ecu Power, and A11. Measured Volts, got like .2V or arround there. I Will try and see if i can boost later. Also, when i set Fixed Duty Cycle, why do it say -1...
- Sat May 08, 2010 9:53 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
Oscilloscope/ ohm meter would probably let u check it. update POWER Wire DIRECT TO POSITIVE Battery Term key off/engine off = 12.7V [bat voltage] key on/engine off = 0.80V Engine running = 4.6V Should it not read 12V Because DATA PANE SHOWS Ebc Input Switch is Checked AND Ebc Active is Checked ? Ca...
- Sat May 08, 2010 7:16 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
- Sat May 08, 2010 4:04 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
- Sat May 08, 2010 3:33 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
- Fri May 07, 2010 8:59 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
- Fri May 07, 2010 1:11 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
Your Error is there : EBC Activation EBC Activation should be read as : TARGET BOOST I had the same problem too, trying to figure out what everything meant. I think Calvin should make things easier to understand :) I Cannot even get the soleniod to click. Should it click if i put, EBC Activation as...
- Thu May 06, 2010 5:48 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12676
EBC Wont WORK!
So i Have a Mac Soleniod Tial 38mm Wg Setup the soleniod according to the instructions EBC Settings: Always on EBC Activation : 0.71psi Fast Spool Duty 50% Wastegate Activation 8.05Psi Fixed Duty Cycle : 50% Soleniod Config A11 Normally Closed Frequence: 25hz Anyone wanna give me any tips?