Search found 220 matches
- Mon Jul 12, 2010 11:32 am
- Forum: Software Support
- Topic: When left the gas over 4000rpm, CEL turns on and get O2 ..
- Replies: 12
- Views: 15876
- Sat May 22, 2010 7:59 am
- Forum: Software Support
- Topic: FINAL BUGS CALL!!!
- Replies: 63
- Views: 72684
- Sat May 22, 2010 7:50 am
- Forum: Software Support
- Topic: Weird EBC issue
- Replies: 26
- Views: 24238
Tell me if I am theoretically wrong, rather than pointing me to do a work around. FACT : My boost controller is always closed and it does not send any pressure to the waste gate (always full/over boost) at 0% DC. It is a fact and I have tested it by disconnecting the wire, and also tried it by disa...
- Sat May 22, 2010 7:37 am
- Forum: Software Support
- Topic: Weird EBC issue
- Replies: 26
- Views: 24238
dude. seriouslly!!!! why are you still asking these questions?????? im not trying to be a dick, but just hook the damn solenoid up the way the every one is telling you too (the correct way)and re configure the ebc settings starting from scratch. it is a normally closed solenoid so use it the right w...
- Tue May 18, 2010 9:14 am
- Forum: Software Support
- Topic: Weird EBC issue
- Replies: 26
- Views: 24238
yes but it was backwardss, so it was actually nomally closed. in the last update it was corrected so now NO is NO and NC is NC. so if i understand right you started having these problems since the last update, which makes since since that solenoid is a NC one. so once again, hook up the vac lines co...
- Mon May 17, 2010 9:02 am
- Forum: Software Support
- Topic: Weird EBC issue
- Replies: 26
- Views: 24238
http://forum.ectune.com/viewtopic.php?t ... c&start=15 check this out to see how vacuum lines should be hooked up
- Mon May 17, 2010 8:59 am
- Forum: Software Support
- Topic: Weird EBC issue
- Replies: 26
- Views: 24238
Just put it the way everyone else does.. start there, once you figure that out, do whatever. listen to top mount!!!!! he knows his shit. set the ebc up how everyone else is using it and start from there. if you set it up a long time ago and then re tuned, it is possible something was changed in the...
- Tue May 11, 2010 8:32 am
- Forum: Software Support
- Topic: Weird EBC issue
- Replies: 26
- Views: 24238
how are ur vacuum lines hooked up? what kind of solenoid is it? if it is the mac solenoid from xenocron or ectune it is a normally closed solenoid. internal or external waste gate. did you just set it up or have u had it and you are now having problems? did you solder the components in ur self? what...
- Sat May 08, 2010 12:59 pm
- Forum: Software Support
- Topic: EBC Wont WORK!
- Replies: 11
- Views: 12509
- Tue Apr 20, 2010 8:22 am
- Forum: Software Support
- Topic: FINAL BUGS CALL!!!
- Replies: 63
- Views: 72684
fuel cut does not work properly. After reaching the cut rpm, the fuel cut light flashes instead of remaining solid. I had to turn off fuel cut and tune it. fuel cut works great for me. what is ur mbar activation set at? it is probably too low. the fuel cut bugs were fix a couple of months ago, and ...
- Sat Apr 17, 2010 11:58 am
- Forum: Software Support
- Topic: FINAL BUGS CALL!!!
- Replies: 63
- Views: 72684
i have my units set to inhg for vacuum columns, and i have my boost columns set to PSI, now when i play back a log file and use the graphs, ebc current, and ebc target are still shown in M bar while boost reads PSI and MAP read vacuum/PSI. yet when i play back the file and watch my data bar, target ...
- Sun Apr 04, 2010 12:40 pm
- Forum: Software Support
- Topic: After upload cal - EBC normally closed is always set
- Replies: 34
- Views: 39067
- Fri Apr 02, 2010 5:15 pm
- Forum: Software Support
- Topic: After upload cal - EBC normally closed is always set
- Replies: 34
- Views: 39067
I dont think NC and NO are backwards anymore since the last update. Mine is set on NO and it works like its supposed to. Im also not having any datalogging issues. what solenoid are you useing???? i am using the mac from xenocron and it is a n/c solenoid but i have to run it in normally open still....
- Thu Apr 01, 2010 9:04 am
- Forum: Software Support
- Topic: License Update
- Replies: 3
- Views: 3861
- Sat Mar 20, 2010 9:02 am
- Forum: Software Support
- Topic: After upload cal - EBC normally closed is always set
- Replies: 34
- Views: 39067