Search found 103 matches
- Sat Jul 26, 2008 4:06 pm
- Forum: Dyno Results
- Topic: All Motor H22 ITB'S TypeR Trans 318hp 228tq
- Replies: 24
- Views: 30814
- Sat Jul 26, 2008 2:58 am
- Forum: Dyno Results
- Topic: All Motor H22 ITB'S TypeR Trans 318hp 228tq
- Replies: 24
- Views: 30814
- Tue Mar 04, 2008 3:04 pm
- Forum: Dyno Results
- Topic: Stock sleeve LS/VTEC plus booooost
- Replies: 1
- Views: 3218
Stock sleeve LS/VTEC plus booooost
This is kind of a sad post, customer got 30-40 miles on the car and did the good old fashioned 1-2-3-2 shift, now exhaust valves on cyls 2 and 3 don't close. Hopefully it just needs valves/guides replaced. Stock sleeve LS/VTEC block with pistons/rods RC750cc injectors Spoolin Performance mini-ram an...
- Fri Feb 29, 2008 1:38 pm
- Forum: Dyno Results
- Topic: stock b16a 57trim@7psi
- Replies: 10
- Views: 7891
Not much of a dyno shop if they don't have a spare MBC or five laying around they can loan you during the tune session. :? Your torque is flat as a strap because there's no restriction to flow on your setup, yet. When the cam, IM, turbine, compressor - or most likely log manifold - starts being a re...
- Sun Feb 10, 2008 12:38 am
- Forum: Dyno Results
- Topic: Sleeved D16Z6, RC750, Crower stage 2 cam, Disco-P
- Replies: 7
- Views: 8852
- Sun Feb 10, 2008 12:36 am
- Forum: Dyno Results
- Topic: Stock LS BOosted 407HP 308TQ
- Replies: 22
- Views: 17779
I thought the old AEM 3 bolt gears were dished, and all the newer gears were the 23-802 five bolt setup? Regardless, if those are AEM then that is who SSAC copied. Reviewing the video where you zoom in on them at ~1:40 it looks like there is some non-SSAC engraving to the right side I can't make out...
- Sun Feb 10, 2008 12:30 am
- Forum: Dyno Results
- Topic: Stock sleeve D16Z6, stock head, SC34, RC440
- Replies: 9
- Views: 8149
- Sat Feb 09, 2008 2:21 am
- Forum: Dyno Results
- Topic: 82mm stock sleeve LS, 11.5:1, 404s
- Replies: 7
- Views: 6552
- Sat Feb 09, 2008 2:14 am
- Forum: Dyno Results
- Topic: Stock LS BOosted 407HP 308TQ
- Replies: 22
- Views: 17779
- Thu Feb 07, 2008 5:05 pm
- Forum: Dyno Results
- Topic: 82mm stock sleeve LS, 11.5:1, 404s
- Replies: 7
- Views: 6552
I suspect it'd do a hair better than 180s. The torque peaked at 6400, right as the exhaust choked. With bigger exhaust the torque would carry on out to 8000 without falling off, same as Sewell's 404 car, and the car would make ~195 to pull a random figure out of my hat. Just conjecture, you never re...
- Thu Feb 07, 2008 4:54 pm
- Forum: Dyno Results
- Topic: Stock sleeve D16Z6, stock head, SC34, RC440
- Replies: 9
- Views: 8149
- Wed Feb 06, 2008 12:28 am
- Forum: Dyno Results
- Topic: 82mm stock sleeve LS, 11.5:1, 404s
- Replies: 7
- Views: 6552
82mm stock sleeve LS, 11.5:1, 404s
This was a fun setup. No matter how I played with timing, AFRs, and cam timing - with the exception of losing power once or twice due to bad cam gear settings - I made the same power as I did the very first dyno pull. LOL. Notice how power flat spots at 6.5K: http://i256.photobucket.com/albums/hh166...
- Wed Feb 06, 2008 12:14 am
- Forum: Dyno Results
- Topic: Sleeved D16Z6, RC750, Crower stage 2 cam, Disco-P
- Replies: 7
- Views: 8852
- Tue Feb 05, 2008 11:56 am
- Forum: Dyno Results
- Topic: Sleeved D16Z6, RC750, Crower stage 2 cam, Disco-P
- Replies: 7
- Views: 8852
Sleeved D16Z6, RC750, Crower stage 2 cam, Disco-P
http://i256.photobucket.com/albums/hh166/joeymisanthropy/Tuning/Dang%20Old%20Rob/blossfield_02.jpg http://i256.photobucket.com/albums/hh166/joeymisanthropy/Tuning/Dang%20Old%20Rob/blossfield_00.jpg Pretty fun setup, you don't see many making this sort of power. I tuned it a few years back, made 248...
- Tue Feb 05, 2008 11:03 am
- Forum: Dyno Results
- Topic: Stock sleeve D16Z6, stock head, SC34, RC440
- Replies: 9
- Views: 8149
Got a set of RC750 for the car and retarded the cam timing 3 degrees. Graphs certainly look healthier! Kinda surprised me as the engine reputedly hasn't been decked/milled any significant amount. Maybe the aftermarket cam gear isn't terribly precise? 240 whp at 12 psi: http://i256.photobucket.com/al...