just switched to Neptune myself because of this. eCtune is awesome, but this is nuts.cquence wrote:This is the main reason I made the switch to Neptune. No force update and software lock out.. good luck guys
Search found 25 matches
- Mon Mar 01, 2010 10:03 pm
- Forum: Software Support
- Topic: ectune wont open
- Replies: 11
- Views: 19037
- Sun Oct 11, 2009 8:36 pm
- Forum: Track Results
- Topic: 11.56 @ 123 mph - b16 stock sleeves 14 psi
- Replies: 3
- Views: 6994
- Sun Apr 05, 2009 7:53 pm
- Forum: Track Results
- Topic: 11.56 @ 123 mph - b16 stock sleeves 14 psi
- Replies: 3
- Views: 6994
11.56 @ 123 mph - b16 stock sleeves 14 psi
UPDATE: went to the track 4-18-09. little better.. best run was R/T 0.037 60' 1.818 330 5.023 1/8 7.565 MPH 96.52 1000 9.738 1/4 11.563 MPH 122.90 time for bigger tires. bouncing off 8800 rev limit about 50-75 feet before the stripe. i think i can pull 1-2 more MPH. bigger tires = better 60's = lowe...
- Tue Mar 31, 2009 2:03 pm
- Forum: Dyno Results
- Topic: b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
- Replies: 11
- Views: 14130
with me in the car, it weighs 2060 lbs. 311 hp and 2060 lbs should be good for low 11's. will post after i find out this weekend. only problem i have is the rev limit. i will be running out of 4th gear at a 1000 ft i think and i don't want to go to 5th. i may increase rev limit to 9000 for 4th gear ...
- Mon Mar 30, 2009 5:18 pm
- Forum: Dyno Results
- Topic: b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
- Replies: 11
- Views: 14130
- Mon Mar 30, 2009 11:41 am
- Forum: Dyno Results
- Topic: b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
- Replies: 11
- Views: 14130
- Mon Mar 30, 2009 10:28 am
- Forum: Dyno Results
- Topic: b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
- Replies: 11
- Views: 14130
- Sun Mar 29, 2009 6:02 pm
- Forum: Dyno Results
- Topic: b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
- Replies: 11
- Views: 14130
- Sun Mar 29, 2009 2:31 pm
- Forum: Dyno Results
- Topic: b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
- Replies: 11
- Views: 14130
b16 t3/t4 60 trim .63 on 15 psi - 311hp/220ft-lb
85 crx hf b16 bored 81.5mm stock sleeves wiesco 9:1 crower econo rods acl race bearings supertech springs and retainers stock valves and LMA's all gaskets and seals are OEM honda and are new gsr cams skunk2 cam gears garrett 60 trim .63 hot side turbo rev hard cast mani (their 600 hp version suppose...
- Sat Mar 21, 2009 5:01 pm
- Forum: Software Support
- Topic: Force update to R9 now error
- Replies: 81
- Views: 95014
- Tue Mar 10, 2009 5:35 pm
- Forum: Automotive Tech
- Topic: where do you guys get your SK5151 or IR6220's from?
- Replies: 7
- Views: 6949
- Sat Sep 20, 2008 2:12 pm
- Forum: Automotive Tech
- Topic: Need ecu help for EBC
- Replies: 5
- Views: 3916
i have the same ecu. i am going to add EBC as: IAB/Autolockup EBC(A17): Add IC16 SK51515 or similair ADD d13 1n4004 (1N4004DICT-ND) This makes the A17 as 12+ volt output.... not sure when i'm going to get to this. race season is over here and it might be a month or so. post up what you get working. ...
- Thu Jul 17, 2008 8:14 pm
- Forum: Automotive Tech
- Topic: Screw-in vs. Bolt-on IAT sensors?
- Replies: 6
- Views: 4442
Re: Screw-in vs. Bolt-on IAT sensors?
I'm getting a weird reading and i was hoping it was just a glitch in crome but i am getting the same reading in eCtune. I have the EuroR intake manifold for my h23vtec and you have to use an accord IAT sensor which is a threaded type sensor. The engine runs fine and it doesnt appear to be having an...
- Sun Jun 08, 2008 8:39 pm
- Forum: Automotive Tech
- Topic: ECT. how hot is too hot?
- Replies: 6
- Views: 4879
might want to check for any air in the coolant system too. i also saw really high temps when i was running just plain water. added some purple ice and that brought my temps down 15 degrees. my car is a drag only car, after burnout temps would be around 175 and at the end of a 1/4 mile they were 215....
- Mon Jun 02, 2008 2:24 am
- Forum: Software Support
- Topic: Very odd interface/app bug...
- Replies: 6
- Views: 4153
I get that \"save marker errored with: Unable to read beyond the end of the stream.\" error all the time. It will usually happen after I've been running the program a while and have made a bunch of changes. Other than that there are no \"i did that and this happens\" time scenarios. Datalogging stop...