eCtune

Topmount, thanx for the response, unfortunately this did not seem to work. I tried to follow your steps, also tried them the other way round in terms of decreasing values, but the engine behaves very similarly. Moreover, when I made the suggested changes to increase fuel values, even starting after ...

Guys, I came to a strange issue. B16 engine, JRSC compressor and 450cc DSM injectors. Once the bigger injectors were put and the JRSC took place, I'm having issues with starting the engine when warm. AFR on idle is fine, multiplier was recalculated using \"new injectors size\" value in Ectune. When ...

No i did not. I tested on the sim for quite some time. I can simulate condition you would not get in car. There i saw that it wasn't working correctly. It's now truly MAP based. I the prev 63 there was a bug that the map value was messed up. I can post a few logs Ok, I did another pull today. Fuelc...

I have a log and a cal I can send you of getting the oxygen sensor mil during a fuel cut. Its only done it once to me thus far. Also, my motor has around 500mbar of manifold pressure at a 1000rpm idle. I have delta reground cams that are .455" lift with about 230 duration at .050". This makes it ha...

I don't see how you guys are having this issue.. I don't have these issues. .. I always use race only ecu in the basmap creator, mabey somthing that get disabled there is affecting it and thats why I don't have this issue.. I also use race ecu when creating basemap. Tried to play with the mbar valu...

fixing so realtime update is not working at all is it enabled in the emulator menu? Tested today. Ostrich 1, latest firmware, all worked fine with previous version release 8. Now it seems realtime update works only a few seconds at the beginning(tested with my favourite Kill Injectors function), th...

All problems persist, my CAL and LOG files are posted in a different topic: http://forum.ectune.com/viewtopic.php?p=17166#17166

Ok, attached is a darkb16a1.zip file. It contains the following files: basemap.cal - my actual basemap fuelcut_minus70.elf - a pull on 3rd gear with no throttle, and with fuel cut set to -70mbar fuelcut_minus70againslightthrottle.elf - a pull on 3rd gear with no throttle at the start and then slight...

Hi, with the new R9 version I noticed to have two problems. 1) Realtime update does not seem to work properly, already discussed in different topic so just a quick note here 2) Datalog rate is much lower than with previous R8 which was working flawlessly for me. When using the R9, the rate of datalo...

fuelcut baro what are you talking about? I was talking about the possibility to disable the "minimum mbar" value for the fuelcut to work. Simply use the TPS value and don't care about the mbar values... as an option for those that have issues with current fuelcut. I will do a pull today and post my...

Yep, the same here. Can anyone post his .cal and log from datalogging ? I was about to do that when I have time but I'm quite busy now.

I have exactly the same problem as racepak. Drive out - WOT - watch the mbar values from approx 6K RPM up to 2500. Values are somewhere between 160-210 mbar. Set the fuelcut to 220-230, TPS 1%. When RPMs are around 3000, fuelcut stops working and car starts to jump. So I raise the fuelcut baro value...

What version do you have ? My 3.0 was too old, after updating to 3.5 SP1 problem is solved.

Guys, you need to update your .NET Framework to the latest version available. That will solve the problem. I had the same issue on my laptop, the crash is caused by incompatibility of Ectune with older dll from .NET framework(mscorwks.dll)

Hi guys, has anyone come across the situation when you have a new laptop and you need to move your current license and registered ostrich to the new laptop? What is the best way ?