Search found 29 matches

by fireztorm
Sat Sep 20, 2008 10:47 pm
Forum: Software Support
Topic: error codes
Replies: 7
Views: 4802

i see 8
by fireztorm
Fri Sep 19, 2008 4:04 pm
Forum: Software Support
Topic: error codes
Replies: 7
Views: 4802

it works now. i disabled the sensors. but i cannot set the settings in boost table. if i go into boost table and set the \"add 120% fuel per psi\" and \" retard timing 0,75\" settings on and then press apply nothing happens, and if i go into the boost table again then nothing happens to the settings.
by fireztorm
Wed Sep 17, 2008 6:18 pm
Forum: Software Support
Topic: error codes
Replies: 7
Views: 4802

ok i shall try that. but when i drive my car there is a rev limiter at 3500rpm why? and i can not change the settings in the boost table setup.
by fireztorm
Wed Sep 17, 2008 3:05 pm
Forum: Software Support
Topic: error codes
Replies: 7
Views: 4802

error codes

i just tryed ectune now and i get these error codes: Electrical Load Detector defective circuit or unplugged / defective sensor. And BARO Sensor (Atmospheric Pressure) defective circuit or unplugged / defective sensor. what could be wrong?
by fireztorm
Fri Aug 01, 2008 12:52 am
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

ok.. thanks :) will try that
by fireztorm
Fri Aug 01, 2008 12:36 am
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

okok.. but what parts am i missing now? i can see on the link he is using a chip.. i do not need that? i have ribbon cable and ostrich to use with ectune..
by fireztorm
Fri Aug 01, 2008 12:28 am
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

if you look at the first picture on the link http://www.superhonda.com/tech/honda_ec ... mming.html you can see the ting marked on the attachment picture i do not have that. and the first picture on the link was when he had not touched anyting.
by fireztorm
Fri Aug 01, 2008 12:21 am
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

OMG :( so i can buy them and set them in there and then it will work? where can i buy them?
by fireztorm
Thu Jul 31, 2008 11:39 pm
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

the ecu hasnt been chipped before. it was in factory condition before i bought the ostrich and hulog. here is pictures of my ecu. http://i38.photobucket.com/albums/e106/ ... G_2030.jpg http://i38.photobucket.com/albums/e106/ ... G_2031.jpg
by fireztorm
Thu Jul 31, 2008 1:26 pm
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

but do you know why i have a solid cel at KOEO?
by fireztorm
Thu Jul 31, 2008 1:02 pm
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

on the picture you sendt later in this post about the J1 i can see that you have a 304 number on your OKI. and the map in ectune is named: stock p28 304 USDM map. on mine OKI is stands: 208.. is this right?
by fireztorm
Thu Jul 31, 2008 11:48 am
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

when KOEO i hear a buzzing sound from my injectors. and i have a solid cel
by fireztorm
Thu Jul 31, 2008 11:15 am
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

now im getting a solid cel and my engine wont start. what now?
by fireztorm
Wed Jul 30, 2008 11:14 pm
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

ok, thanks! :) i will try tomorrow.
by fireztorm
Wed Jul 30, 2008 11:07 pm
Forum: Software Support
Topic: will not connect to ecu
Replies: 50
Views: 29365

ok, but i still have problems with my datalogging. or does this fix that to? it tells me that i cannot connect to the ecu. i have cut j12 and im running a hulog extreme. what can be wrong here?