Search found 290 matches
- Thu Nov 18, 2010 4:28 pm
- Forum: Software Support
- Topic: Dwell ignition on an F22b2.....
- Replies: 8
- Views: 7344
Can't seem to get this question out of my mind. I've tried goolge for some time, and there's no straight forward answer. My doubt is, let's say I have a d16z6, and for some reason , I want to start my cal using the p30 base cal. Do all honda ignition systems(b series, d series, f and h series...) sh...
- Wed Nov 17, 2010 7:41 pm
- Forum: Software Support
- Topic: AEM Serial Wideband
- Replies: 24
- Views: 26647
- Fri Nov 12, 2010 6:02 pm
- Forum: Software Support
- Topic: AEM Serial Wideband
- Replies: 24
- Views: 26647
AEM serial logging works great, but I've noticed that the values implemented in eCtune and other tuning programs are a bit off.I think that the specs provided by AEM are off too(possibly). I had a car of mine running an AEM wideband on d14, and using the AEM values table, I was idling around 14.6 on...
- Tue Nov 02, 2010 5:19 pm
- Forum: Software Support
- Topic: Idling problems
- Replies: 4
- Views: 5205
- Thu Oct 28, 2010 12:46 pm
- Forum: Software Support
- Topic: Launch control & full throttle shift issues
- Replies: 9
- Views: 8912
I had a similar issue yesterday. I'm using a single user license. In my case, the car would use launch control as a rev limiter. If I had the rev limiter set at 7000, and launch control at 6000, it would rev cut at 6000 in any gear. Not sure if it was related to full throttle shifting, I didn't test...
- Fri Oct 15, 2010 6:33 pm
- Forum: Track Results
- Topic: F22 Accord @ 10 psi
- Replies: 10
- Views: 16421
- Fri Oct 15, 2010 1:45 pm
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
When I started my cal, I used a stock p28 rom, started by adding +%20 on the injector offsets. Did a street tune on openloop only. Had afr's set up good enought under all loads, then finished the cal and had the car run on closeloop till 700-750 mbar. As it sits, the car runs ok, but I noticed that ...
- Sat Oct 09, 2010 9:57 am
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
Would o2 fuel trim be in any way related to injector offset? The reason I ask is because when I started my calibration, I used a p28 rom, and I had to add +20 on the injector offset section to get idle good. Yesterday, I changed o2 trim from -15 to -20 and the car is acting better than before. So th...
- Tue Oct 05, 2010 10:49 pm
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
- Fri Oct 01, 2010 4:47 pm
- Forum: Software Support
- Topic: Fuel cut doesn't seem to work consistantly....
- Replies: 10
- Views: 27787
- Fri Oct 01, 2010 4:38 pm
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
- Fri Oct 01, 2010 12:40 pm
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
- Fri Oct 01, 2010 12:14 pm
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
- Wed Sep 29, 2010 5:02 pm
- Forum: Software Support
- Topic: Question about closeloop.....
- Replies: 17
- Views: 15167
Question about closeloop.....
Just wondering if anyone has good tips to get closeloop to work \"smooth\". I have closeloop enabled till 730 mbar, but in between 1100-1800 rpm, the car feels like it jerks slightly back and forth, very minimal. When looking at the datalog, the jerking is felt when the car goes from rich to lean(be...
- Wed Sep 22, 2010 12:59 pm
- Forum: Software Support
- Topic: eCtune burn2
- Replies: 9
- Views: 7642