Search found 49 matches
- Sun Nov 15, 2009 10:45 am
- Forum: Software Support
- Topic: Calvin, Got a new laptop...What to do...
- Replies: 3
- Views: 4280
Calvin, Got a new laptop...What to do...
Do I dowload and request license, then once I get, register ostrich? Or load pro_ostrich from old computer?
- Wed Aug 05, 2009 11:48 am
- Forum: Automotive Tech
- Topic: High idle...white smoke
- Replies: 10
- Views: 6945
I thought the piece that goes through the IM was just a fitting that would easily come out. well it was previously broken so I took it out, not knowing, and ran a strait hose to the breather. I now know what a pcv valve actually is. I blocked off the intake mani, that brought idle to normal, and no ...
- Wed Aug 05, 2009 1:47 am
- Forum: Automotive Tech
- Topic: High idle...white smoke
- Replies: 10
- Views: 6945
- Mon Aug 03, 2009 11:45 pm
- Forum: Automotive Tech
- Topic: High idle...white smoke
- Replies: 10
- Views: 6945
- Mon Aug 03, 2009 11:17 pm
- Forum: Automotive Tech
- Topic: High idle...white smoke
- Replies: 10
- Views: 6945
- Mon Aug 03, 2009 10:34 am
- Forum: Automotive Tech
- Topic: High idle...white smoke
- Replies: 10
- Views: 6945
- Sun Aug 02, 2009 6:31 pm
- Forum: Automotive Tech
- Topic: High idle...white smoke
- Replies: 10
- Views: 6945
High idle...white smoke
Newly built motor. Gsr bottom rebuilt B16 head w/ crower S&R ITR Intake mani Stock Exhaust mani CTR cams Arp head bolt new head gasket B16 auto trans w/LSD LC-1 wideband wired into P30 ECU running stock Type R cal I got cel for IACV and primary O2 heater, disabled O2 and plugged up Iacv. after that ...
- Thu Jun 25, 2009 1:24 pm
- Forum: Automotive Tech
- Topic: B16 auto tranny setup...
- Replies: 30
- Views: 21748
Is the car body manual or auto? When I did the manual to auto conversion n my 92 SI, I swapped everything over from my 94 EX auto. OBD1 auto trans are hydraulically controlled, OBD2 and up are electronic. the P28 auto ECU for(M24) would be preferred, but it depends on the trans model. Give more info...
- Wed Mar 25, 2009 4:22 pm
- Forum: Automotive Tech
- Topic: 4 bar MAP sensor
- Replies: 4
- Views: 5119
- Wed Mar 25, 2009 3:41 pm
- Forum: Automotive Tech
- Topic: 4 bar MAP sensor
- Replies: 4
- Views: 5119
- Wed Mar 25, 2009 2:29 pm
- Forum: Automotive Tech
- Topic: 4 bar MAP sensor
- Replies: 4
- Views: 5119
4 bar MAP sensor
Can I install a 4bar senor with Pro, and be fine with a stock motor?
- Mon Mar 23, 2009 12:45 pm
- Forum: Automotive Tech
- Topic: Alternator or Electrical problem?
- Replies: 4
- Views: 5262
- Sun Mar 22, 2009 7:53 pm
- Forum: Automotive Tech
- Topic: Alternator or Electrical problem?
- Replies: 4
- Views: 5262
Alternator or Electrical problem?
When I 1st put in KOEO position I get code 3, but CEL shut off like normal. Car starts like normal, run fine, then 3 miles later, I start to get power failure. Got a jump, and 1/4mi power failure again. repeated the same type of jump and same happened again. the time I jumped it, I let it charge lon...
- Sat Mar 21, 2009 6:54 pm
- Forum: Automotive Tech
- Topic: B16 auto tranny setup...
- Replies: 30
- Views: 21748
- Sat Mar 21, 2009 6:00 pm
- Forum: Software Support
- Topic: Do I need a new license?
- Replies: 1
- Views: 1984
Do I need a new license?
I had to completely erase and reprogram my laptop. I previously had the Pro version, now its not acting right. I'm supposed to put the license in the eCtune folder in C; drive correct?