600 HP B16A2
Moderator: Gaskleppie
- ge0ne
- <font color=green>eCtune Authorized Tuner</font>
- Posts: 147
- http://phpbb3styles.net
- Joined: Mon Apr 09, 2007 2:48 pm
- Location: Greece
600 HP B16A2
It was time to post it, a few months ago, i tuned a turbo EK B16. Car made 602hp at 8670rpm and 52.3kg of torque at 8182. Only that we couldn't measure it till the rev limiter cause it continually spin on the rollers after 8600... Rev limit is at 9600. Car runs on 2 bar with an 60-1 and is fully built. 84mm CP pistons Pauter rods Darton sleeves Crower cams Full Ferrea valvetrain Port and polish Ram horn Manifold 3'' exhaust Turbosmart external 1000cc injectors Prodrive 280lt/h pump Aebs I/M Precision I/C MSD 6AL Ignition Big thumbs up also go to Xenocron, for making lot of this parts come in Greece in time
- Attachments
-
- Εικόνα021.jpg (729.29 KiB) Viewed 3654 times
Regards, George Nerantzis diasiq eCtune Team eCtune Authorized Tuner Location: All over Greece
- xenocron
- <font color=green>eCtune Authorized Tuner</font>
- Posts: 1012
- Joined: Wed Apr 04, 2007 7:00 pm
- Location: New Jersey
- Contact:
Nice job George! Track times?
Regards, Xenocron Tuning Solutions eCtune Team eCtune Authorized Tuner Location: Ringwood, NJ / Hillburn, NY U.S.A. www.xenocron.com DIY ECU Chipping, Fuel Management Parts and more...
- ge0ne
- <font color=green>eCtune Authorized Tuner</font>
- Posts: 147
- Joined: Mon Apr 09, 2007 2:48 pm
- Location: Greece
I know you would be interested, car will hit the track at september. But not much expected due to its weight (car is a 4 door). Either way after some secret test results car did a 12 sec pass with 220km/h exit on the 1/4 mile
Regards, George Nerantzis diasiq eCtune Team eCtune Authorized Tuner Location: All over Greece
- yc underground
- <font color=green>eCtune Authorized Tuner</font>
- Posts: 114
- Joined: Mon Apr 09, 2007 4:29 pm
- Location: York, PA
- Contact:
x2
Regards, eCtune Team eCtune Authorized Tuner Location: York, PA, USA www.ycunderground.com www.facebook.com/YCUDynoTuning
- ge0ne
- <font color=green>eCtune Authorized Tuner</font>
- Posts: 147
- Joined: Mon Apr 09, 2007 2:48 pm
- Location: Greece
And a video from the car on the dyno... Remember car spinned after 8500 rpm it had 1000 more to go. Tuned on 2 bar (29 PSI)... Video is dedicated to Chris AKA Xenocron. Video here --> http://youtube.com/watch?v=PaEHBR-b3rE Sound is bad when Vtec kicks in...
Regards, George Nerantzis diasiq eCtune Team eCtune Authorized Tuner Location: All over Greece
- xenocron
- <font color=green>eCtune Authorized Tuner</font>
- Posts: 1012
- Joined: Wed Apr 04, 2007 7:00 pm
- Location: New Jersey
- Contact:
Sick stuff Georgey pooge0ne wrote:Video is dedicated to Chris AKA Xenocron. Video here --> http://youtube.com/watch?v=PaEHBR-b3rE Sound is bad when Vtec kicks in...
Regards, Xenocron Tuning Solutions eCtune Team eCtune Authorized Tuner Location: Ringwood, NJ / Hillburn, NY U.S.A. www.xenocron.com DIY ECU Chipping, Fuel Management Parts and more...