Stock LS, Greddy 18G 249.2whp/246.5wtq

eCtuned dyno results.

Moderator: Gaskleppie

TheGuardian
Posts: 59
http://phpbb3styles.net
Joined: Sun Dec 07, 2008 7:01 pm
Location: Lima, OH

Stock LS, Greddy 18G 249.2whp/246.5wtq

Post by TheGuardian »

Stock LS with 120,000 miles on the clock Greddy 18G w/ Greddy exhuast manifold MAC boost controller set @13psi 3\" custom downpipe 3\" Thermal R&D Exhaust RC 550cc injectors Walbro 255 Greddy Intercooler and piping Turbo XS RFL Bov Tuned by Matt Shue in Richmond VA With a goal of 250whp I'm very happy with the results. 249.2whp/246.5wtq Image On the dyno Image

sgtmillhouse648
Posts: 18
Joined: Wed Jun 24, 2009 9:00 am
Location: Blue Grass, IA

Post by sgtmillhouse648 »

Very sharp! Are you still utilizing the GReddy elbow or did you step up to something less restrictive?

TheGuardian
Posts: 59
Joined: Sun Dec 07, 2008 7:01 pm
Location: Lima, OH

Post by TheGuardian »

sgtmillhouse648 wrote:Very sharp! Are you still utilizing the GReddy elbow or did you step up to something less restrictive?
Na, I did away with that restrictive piece of junk... I replaced it with a Custom 3" Downpipe, helps her spool earlier thats for sure: Image

User avatar
ckretvix
Posts: 251
Joined: Thu Jan 22, 2009 9:29 pm
Location: Indiana

Post by ckretvix »

I made very similar #'s (254/244) with a pretty much identical setup at 11 psi. Put a cutout or open dp and you will see 10-15 more whp.

Bugermass
<font color=gray>Site Admin</font><br><font color=green>eCtune Authorized Tuner</font>
Posts: 1632
Joined: Tue Apr 03, 2007 2:17 pm
Location: Houston Texas

Post by Bugermass »

Thats good power for a greddy kit.. The most I've ever gotten out of the greddy kit on a LS was about 275@ 18 PSI.. Didn't really wanna push my luck much more than that cause I could tell from the fueling that the backpressure was already getting pretty high on the top end.. I'll post that map if you want to compare..
Chris Delgado Tun'd Performance Houston Texas 713-962-8262

User avatar
ckretvix
Posts: 251
Joined: Thu Jan 22, 2009 9:29 pm
Location: Indiana

Post by ckretvix »

Id like to see it =).

TheGuardian
Posts: 59
Joined: Sun Dec 07, 2008 7:01 pm
Location: Lima, OH

Post by TheGuardian »

^Same I've been told the 18G is limited to about 300hp, 18psi is up there, I can't imagine this turbo is very efficient in that range.

Bugermass
<font color=gray>Site Admin</font><br><font color=green>eCtune Authorized Tuner</font>
Posts: 1632
Joined: Tue Apr 03, 2007 2:17 pm
Location: Houston Texas

Post by Bugermass »

I'll post it tommorrow when I have my laptop up.. Its in the car right now, to lazy to go get it. ;)
Chris Delgado Tun'd Performance Houston Texas 713-962-8262

Bugermass
<font color=gray>Site Admin</font><br><font color=green>eCtune Authorized Tuner</font>
Posts: 1632
Joined: Tue Apr 03, 2007 2:17 pm
Location: Houston Texas

LS Map

Post by Bugermass »

Heres the map Car ran for a year+ on this map at 18PSI before the owner sold the car.
Attachments
Daves Old Program LS TUrbo.cal
(8.1 KiB) Downloaded 235 times
Chris Delgado Tun'd Performance Houston Texas 713-962-8262

TheGuardian
Posts: 59
Joined: Sun Dec 07, 2008 7:01 pm
Location: Lima, OH

Post by TheGuardian »

Only 49% duty cycle on 550ccs...not bad, I would have thought it would be in the 60-70% range but now that I think about it, that sounds about right. Did you have any problems with the 18g's wastegate over 14psi? I've read that you run into boost creep problems with the 18g over 14psi.
Team-Integra member (TheAlpha) Silver Integra LS-T 250whp/246wtq @13psi

Bugermass
<font color=gray>Site Admin</font><br><font color=green>eCtune Authorized Tuner</font>
Posts: 1632
Joined: Tue Apr 03, 2007 2:17 pm
Location: Houston Texas

Post by Bugermass »

nope didn't have any creep issues. The timing was maxed out for the setup and fueling was in the 11.5s ..
Chris Delgado Tun'd Performance Houston Texas 713-962-8262

TheGuardian
Posts: 59
Joined: Sun Dec 07, 2008 7:01 pm
Location: Lima, OH

Post by TheGuardian »

Maxed out as in taken to MBT and retarded 2 degrees?
Team-Integra member (TheAlpha) Silver Integra LS-T 250whp/246wtq @13psi

User avatar
Gaskleppie
<font color=gray>Site Admin</font><br><font color=green>eCtune Authorized Tuner</font>
Posts: 1263
Joined: Tue Apr 03, 2007 11:22 am
Location: Netherlands
Contact:

Post by Gaskleppie »

Nice sharp calibration for a stock block. It can handle a lot of timing! We dont have LS blocks here in Holland.
Regards, eCtune Team eCtune Authorized Tuner Location: The Netherlands

Bugermass
<font color=gray>Site Admin</font><br><font color=green>eCtune Authorized Tuner</font>
Posts: 1632
Joined: Tue Apr 03, 2007 2:17 pm
Location: Houston Texas

Post by Bugermass »

no as in taken to MBT and left there ;)
Chris Delgado Tun'd Performance Houston Texas 713-962-8262

Almighty-Si
Posts: 336
Joined: Sat Apr 14, 2007 2:46 am
Location: N.Y

Post by Almighty-Si »

Sweet ! I thought I was the only who messed with the GReddy kit...LoL...that elbow is a piece of crap and the cause of all the problems with that kit. The stock kit on my B16 made 193whp at 7psi and after the ramhorn manifold, downpipe upgrade (2.5 inch off the turbo) on just under 6psi i made 223whp/272whp on 10psi. I just got the motor built and am about to upgrade the downpipe and exhaust to 3 inch and kicking up the boost to 20psi :D I think you would benefit greatly porting the head. What are the plans now or you going to leave it the way it is? Oh by any chance do you still have the GReddy elbow laying around?

Post Reply