Ostrich Verify
Posted: Mon Dec 17, 2007 8:47 am
I need to know where it goes wrong... Please post you ectune version, ostrich version 1 or 2, ostrich firmware version... Thank you p.s. only the people that have verifiy problems
eCtune
eCtune's official online messageboard community.
https://ectune.hondatuningsuite.com/
Ostrich Verify
Page 1 of 2
Posted: Mon Dec 17, 2007 11:38 am
ectune version: r6 Ostrich: v1 firmware version: 19
Posted: Mon Dec 17, 2007 12:50 pm
ok then i can test i have a ostrich 1 here.
Posted: Mon Dec 17, 2007 4:57 pm
fixed... sort of
Posted: Mon Dec 17, 2007 5:14 pm
ectune version: r6 Ostrich: v1 firmware version: 19 The verify status bar in r6 goes across about 3/4 of the way now, but it still comes up as could not verify.
Posted: Mon Dec 17, 2007 8:48 pm
i fixed it a dirty way. I'm debugging with craig i'll keep everybody posted
Posted: Mon Dec 17, 2007 9:29 pm
people that are having problems please try this..
Posted: Wed Dec 19, 2007 11:52 am
nobody tried this??
Posted: Wed Dec 19, 2007 3:16 pm
I'm back (long story). Anyway: ectune version: r6 Ostrich: v1 firmware version: 18 (I used the firmware update posted above) I tried it about an hour ago. I tried the get rom and now it works. 
I tried the verify rom and it works also but I have to double check something... I opened a totally different cal file than the rom that was in the emulator on purpose to test the verify. When I hit verify it replied the rom had verfied. I found that strange since I knew the cal I had opened in the app was different than the rom in the emu. So I hit get rom and what it got from the emu was the same cal file that I opened on purpose that I knew was differnet to the one in the emu. The I figured that it was the realtime update that was putting it in the emu everytime I opened a different cal. I tried to deactivate it in the drop down menu but it always stayed on. I then checked the settings under the emulator tab and found the \"realtime update always on\". I unchecked it and hit save. When I went the drop down menu again it was on. I returned to the setting emu tab and the \"realtime update always on\" was on again. I unchecked it again saved the the settings and closed ectune. I re-opened ectune and checked the setting emu tab and the \"realtime update always on\" was on again. So... I know it verifies well and the get rom functions also but I could not test the verify with a different file since it puts it in the emu everytime I open one. But is it working. So the steps to duplicate this: 1- Open ectune 2- Connect emulator and hit connect in the menu 3- Hit get rom to make sure what rom is in the emulator. 4- Open a cal file that is different than the rom that is in the emulator. 5- Hit verify It should verify.... then 6- Hit get rom... it should bring the same cal that was opened on purpose (different from the one that was tested in step 3).
I tried the verify rom and it works also but I have to double check something... I opened a totally different cal file than the rom that was in the emulator on purpose to test the verify. When I hit verify it replied the rom had verfied. I found that strange since I knew the cal I had opened in the app was different than the rom in the emu. So I hit get rom and what it got from the emu was the same cal file that I opened on purpose that I knew was differnet to the one in the emu. The I figured that it was the realtime update that was putting it in the emu everytime I opened a different cal. I tried to deactivate it in the drop down menu but it always stayed on. I then checked the settings under the emulator tab and found the \"realtime update always on\". I unchecked it and hit save. When I went the drop down menu again it was on. I returned to the setting emu tab and the \"realtime update always on\" was on again. I unchecked it again saved the the settings and closed ectune. I re-opened ectune and checked the setting emu tab and the \"realtime update always on\" was on again. So... I know it verifies well and the get rom functions also but I could not test the verify with a different file since it puts it in the emu everytime I open one. But is it working. So the steps to duplicate this: 1- Open ectune 2- Connect emulator and hit connect in the menu 3- Hit get rom to make sure what rom is in the emulator. 4- Open a cal file that is different than the rom that is in the emulator. 5- Hit verify It should verify.... then 6- Hit get rom... it should bring the same cal that was opened on purpose (different from the one that was tested in step 3).Posted: Wed Dec 19, 2007 5:11 pm
if you open a calibration and the emulator is connected the cal auto uploads
Posted: Wed Dec 19, 2007 8:26 pm
Is there anyway to stop this from happening?
Posted: Wed Dec 19, 2007 9:21 pm
Just de-select it. It's that easy, but why would you not want to load the cal auto?sohcd16y8 wrote:Is there anyway to stop this from happening?
Posted: Wed Dec 19, 2007 10:08 pm
In my case I de-selected it but it would automatically re-activate itself. In the settings emulator tab there is a check box \"realtime update always on\" I unchecked it and saved but in stays on matter what. No biggie... the verify and get rom works, which is great!
Posted: Thu Dec 20, 2007 2:12 am
No, its in the \"general\" tab. Its called \"Upload rom on emulator connection\"In my case I de-selected it but it would automatically re-activate itself. In the settings emulator tab there is a check box \"realtime update always on\" I unchecked it and saved but in stays on matter what. No biggie... the verify and get rom works, which is great!
Posted: Thu Dec 20, 2007 7:03 am
thank youGaskleppie wrote:No, its in the "general" tab. Its called "Upload rom on emulator connection"In my case I de-selected it but it would automatically re-activate itself. In the settings emulator tab there is a check box "realtime update always on" I unchecked it and saved but in stays on matter what. No biggie... the verify and get rom works, which is great!