Lean Protection Errors?

Post by **calvin** » Thu Feb 28, 2008 11:17 am

let me send a new version to u first... so there is no confusion

Post by **calvin** » Fri Feb 29, 2008 12:32 pm

did u get the r3? test again please make me a log please..

sohcd16y8 · Post by **sohcd16y8** » Fri Feb 29, 2008 1:43 pm

I did get the r3, but it snowed a bit here so I will be testing tonight at the earliest, if not tomorrow. When should we be expecting the VSS fixed r3?

Post by **calvin** » Fri Feb 29, 2008 3:37 pm

sohcd16y8 wrote:I did get the r3, but it snowed a bit here so I will be testing tonight at the earliest, if not tomorrow. When should we be expecting the VSS fixed r3?

fixed it already redownload.. if u want u can keep current. it shows the timer for lean protect 1.. countdown timer.. then u know for sure if lean protect is enabled the timer should be 0. VSS is my debug flag when testing

JaredKaragen · Post by **JaredKaragen** » Fri Feb 29, 2008 4:48 pm

for my info; redownload from the last link you sent me? is it going to be the 0021r3.t0 file? I have already installed this one; so do I need to redownload the same one? (sorry for being confused)

Post by **calvin** » Fri Feb 29, 2008 7:38 pm

same link download

sohcd16y8 · Post by **sohcd16y8** » Fri Feb 29, 2008 9:23 pm

Just got done testing and it works fine. I attached the log in case anyone wants to see it. Also I left the closed loop and ve disable disabled and just disable closed loop since my tune changed a lot with ve disabled. The o2 CEL didnt come on again though, so hopefully it was a fluke. Thanks Calvin!

Post by **calvin** » Fri Feb 29, 2008 9:49 pm

lean protections works fine?

sohcd16y8 · Post by **sohcd16y8** » Fri Feb 29, 2008 10:09 pm

Like a champ!!!!

Post by **calvin** » Fri Feb 29, 2008 10:23 pm

joppez · Post by **joppez** » Fri Jun 24, 2011 1:28 am

I cannot set leanP to work. If i use setup like this it will Icut at minimum rpm (datalog you see is different run)

Like this it will have Icut 4000rpm even on cruising and leanP led is not on. I have innovate MTX-L to D10 and its dead on.

JaredKaragen · Post by **JaredKaragen** » Fri Jun 24, 2011 1:18 pm

I believe I remember seeing leanp 2 did not work correctly. Try just #1 and report back.

joppez · Post by **joppez** » Wed Jul 13, 2011 4:39 am

Now it doesnt do anything, i put max afr 12 on leanp 1 and i had little lean 12.8afr over 15psi and it didnt do nothing? I cannot put anything on \"cut rpm\" Is this setup right or am i doing something wrong? Pic of log here: http://joppen.kuvat.fi/kuvat/d16z6/EMS/ ... 1.jpg/full

joppez · Post by **joppez** » Wed Sep 28, 2011 12:17 am

Still not working, tryed different settings like max afr 10 and still no luck, this feature could save engine if working right so i want it. WB is working because im using WB closeloop.

joppez · Post by **joppez** » Sun Oct 16, 2011 2:02 am

Got it working, changed wbo2 from d10 to d14. But now log afr is not stable its oscillating little bit