datalog and other stuff

chepetrueno · Post by **chepetrueno** » Sun Aug 23, 2009 8:18 pm

hello, i opened a thread in general comments, but here are my troubles, the car starts but only revs to 4000 rpm, and demon will connect to my laptop but wont datalog what can it be, i tested conection in settings and said demon found in com5

Post by **Bugermass** » Sun Aug 23, 2009 10:02 pm

Somthing is wrong with your socket, or how the demon is plugged into the socket, sounds like the ECU isn't reading it. Double check everything..

chepetrueno · Post by **chepetrueno** » Sun Aug 23, 2009 10:06 pm

ok ill check that out tomorrow, anything in particular i should look for, or should i desolder the whole thing and resolder it

Post by **Bugermass** » Mon Aug 24, 2009 10:52 am

just make sure its all the way in there and that the pins are lined up prperly, also you did put the 74HC chip in place too? I've had a couple ecus come in that were missing this.. Somtimes the demons feel like they are all the way in but they are not.

chepetrueno · Post by **chepetrueno** » Mon Aug 24, 2009 2:27 pm

ok thanks, 74hc is in but maybe there is a bad solder in there ill check anyways

Post by **calvin** » Mon Aug 24, 2009 11:41 pm

check wiki.ectune.com it give u the status of the leds how it should and should not be...

chepetrueno · Post by **chepetrueno** » Tue Aug 25, 2009 1:08 pm

i will check the led status, but in the meantime here are some pics of the setup

chepetrueno · Post by **chepetrueno** » Tue Aug 25, 2009 3:12 pm

well i tried as the wiki says and the leds are working normal, red led turns off when emulator is conected and the green one is flashing, could this be an issue with the license? i had another demon installed before this one, i un installed and put the new demon inside it do i need to send calvin the request for another licence to be there?

Post by **calvin** » Tue Aug 25, 2009 3:17 pm

see wiki.ectune.com trouble shooting guide... problem between demon and ecu -cable -j12 -no rom uploaded http://wiki.ectune.com/index.php/Datalo ... on_version

chepetrueno · Post by **chepetrueno** » Tue Aug 25, 2009 9:52 pm

should the j12 be fully removed? also i checked the cn2 port and it looks like its welded properly, the last thing would be the cable also does ectune pairs up to a certain demon, i had another one, and with the last one had no trouble, could this be what is giving me trouble?

Post by **calvin** » Tue Aug 25, 2009 11:30 pm

it looks good you entered the demon serial number right?

chepetrueno · Post by **chepetrueno** » Wed Aug 26, 2009 12:44 am

the number that is on the underside of the demon, i mean the opposite side of the battery? i entered the demon licence that xenocron sent me

Post by **calvin** » Wed Aug 26, 2009 12:58 am

yes j12 needs to be removed completely

HeroOfTheDay · Post by **HeroOfTheDay** » Thu Sep 17, 2009 10:14 pm

I am having the exact same issues. Is this because my registration information hasn't been returned yet? I just registered today, and was told I need to place an XML file in the eCtune directory. Is that correct?

HeroOfTheDay · Post by **HeroOfTheDay** » Fri Sep 18, 2009 11:14 am

My red LED does not turn off when I connect to the emulator. J12 is cut, I uploaded a baserom+calibration, and the CN2 cable is plugged in correctly. Why is the LED still on?