Datalogger won't connect to ecu/Fixed/Hulog cable wrong

OneRM · Post by **OneRM** » Wed Apr 30, 2008 9:18 pm

Ok, so i just got everything setup. Did my ectune update, did my ostrich update, updated my usb ports. Everything is working and I've loaded a basemap however the datalogger won't connect. popup says can't connect to ecu.

Post by **calvin** » Wed Apr 30, 2008 9:42 pm

make sure j12 is cut. Check in device manager which port your datalogging uses.(don't plug in your ostrich). Now that you have the right comm port open settings->datalogging Disable auto-scan Select correct comm port Baud 38400 And press test

boostedeh2 · Post by **boostedeh2** » Wed Apr 30, 2008 11:43 pm

my datalog won't connect unless the key position to \"ON\"...Don't know if that would help.

zex_cool · Post by **zex_cool** » Wed Apr 30, 2008 11:47 pm

that is how it works. key on; datalog on...key off; datalog off.

Post by **calvin** » Thu May 01, 2008 12:35 am

ecu is off if key is off

boostedeh2 · Post by **boostedeh2** » Thu May 01, 2008 12:54 am

OneRM wrote:Ok, so i just got everything setup. Did my ectune update, did my ostrich update, updated my usb ports. Everything is working and I've loaded a basemap however the datalogger won't connect. popup says can't connect to ecu.

yup, did you turn your key on when you were trying to connect?

boostedeh2 · Post by **boostedeh2** » Thu May 01, 2008 12:56 am

OneRM wrote:Ok, so i just got everything setup. Did my ectune update, did my ostrich update, updated my usb ports. Everything is working and I've loaded a basemap however the datalogger won't connect. popup says can't connect to ecu.

yup, did you turn your key on when you were trying to connect?

OneRM · Post by **OneRM** » Thu May 01, 2008 9:06 am

tried with key on and car running, both no go. I'll check j12 to make sure its cut, that may be the problem. I'll keep you posted.

Post by **calvin** » Thu May 01, 2008 9:32 am

hard set the comm port and the baud should be 38400

OneRM · Post by **OneRM** » Thu May 01, 2008 9:39 am

cut j12 and changed to com port 5, with 38xxxx baud setting. Still no change.

Post by **calvin** » Thu May 01, 2008 10:10 am

if you key on how many flashes do you see?

OneRM · Post by **OneRM** » Thu May 01, 2008 11:25 am

how many flashes? where would it be flashing. I don't see any flashes on CEL or in software.... Thanks for the speedy responses btw.

Almighty-Si · Post by **Almighty-Si** » Thu May 01, 2008 12:46 pm

If you have uploaded a basemap when you put the key in the on position your CEL will light then go out, this is where you need to pay attention, the CEL will flash again shortly after the CEL goes out.

Post by **calvin** » Thu May 01, 2008 2:39 pm

Pay close attention what u see and hear if u key on. And let me know. Did you do upload base+calibration?

OneRM · Post by **OneRM** » Thu May 01, 2008 6:02 pm

just did basemap+calibration. still no dice. I do however see 3 flashes if that helps?

eCtune

Datalogger won't connect to ecu/Fixed/Hulog cable wrong

Datalogger won't connect to ecu/Fixed/Hulog cable wrong

Re: Datalogger won't connect to ecu

Re: Datalogger won't connect to ecu